28 gauge.... Thanks man.... U Def need a vtc4 to power this properly.
Sent from my GT-I9500 using Tapatalk
Sent from my GT-I9500 using Tapatalk
Show us your Builds - Kayfun, Russians & Similar
- Thread starter devdev
- Start date
Now to get my hands on a VTC battery, preferably the VTC5
Freaking Awesome coil man. How big is your air holes/ventilation? I managed to drill my Russian Clone to 2mm and it is sucking much better. I was actually rather amazed at the double barrel coil's performance. Thank heavens for RippTrippers. Your coils are superb, neat, and tight like a tiger.
Thanks bro. It's 2mm....its really good at 2mm....it doesn't perform on the vtr at 15w and 6v.needs a mech with a vtc4 then it's popping like crazy
Sent from my GT-I9500 using Tapatalk
Sent from my GT-I9500 using Tapatalk
oh yeah, getting the wire to behave is half the mission. i think i lost about a third of my wire because of knots and springyness
I started coiling with 26g kanthal and worked my way up (or down) to 32g. now the problem is I dont get flavour from the 32g on my KFLP! anyone have the same problem? thinking I should just stay with 26g or maybe go bigger to 24g or 22g
Oki guys here's my opinion of the dual coil I built on my kayfun.
The taste ain't as good as my normal single coil 1.3 ohm builds.
The flavour is good but nothing wow like you would expect from a dual coil. I find the vapour to be more dense on the single coil build.
U need a vtc4 to power a dual coil to get the full potential out of the build. The single coil runs awesome on a vtc4 and pretty good on my vtr.
The wicks... They burn every 2nd day. If they don't burn, they break just as the wick exits the coil. Tried different thickness etc I've this week but no joy.
The throat hit from the dual coil is hard. It thumps the throat. I can lung pull without coughing.
It gets really hot when u chain vape. So hot u can't touch the atty.
My verdict : single coil, 2mm drill bit, between 1 and 1.4ohm is the beauty of the kayfun for me. Thick dense vapour, unbelievable flavour and wicks last a while before u gotta Rewick.
Sent from my GT-I9500 using Tapatalk
The taste ain't as good as my normal single coil 1.3 ohm builds.
The flavour is good but nothing wow like you would expect from a dual coil. I find the vapour to be more dense on the single coil build.
U need a vtc4 to power a dual coil to get the full potential out of the build. The single coil runs awesome on a vtc4 and pretty good on my vtr.
The wicks... They burn every 2nd day. If they don't burn, they break just as the wick exits the coil. Tried different thickness etc I've this week but no joy.
The throat hit from the dual coil is hard. It thumps the throat. I can lung pull without coughing.
It gets really hot when u chain vape. So hot u can't touch the atty.
My verdict : single coil, 2mm drill bit, between 1 and 1.4ohm is the beauty of the kayfun for me. Thick dense vapour, unbelievable flavour and wicks last a while before u gotta Rewick.
Sent from my GT-I9500 using Tapatalk
Kayfun Land deserves no down time!
Rewicked using 26g. It's a parallel coil of 7 wraps around a 1.4mm id. 0.5 ohms. Here are some pics to light up the thread.
Guys I know I probably sound like a broken record player but this is the one! The best vape I've ever had on the Kayfun. Coil is positioned about 1.5mm above the air hole. The throat hit on this one is perfect, not too harsh. I've had a lot of sub ohms build that couldn't really accentuate the flavour because the TH was super intense and the vape too warm. This is just perfect! And as you can see I've used a generous amount of cotton. 10/10 flavour.
Note: Seeing as my Kayfun 3.1's top cap is otherwise occupied at the moment, I needed to use the Lite Plus's top cap, which requires the Lite Plus's chimney base, which is about 2mm shorter than that of the 3.1. I don't know if the smaller chamber contributes to the increased flavour so I'll change it back at some point and leave an update.
And thanks for the credit card insulator tip @Rowan Francis! Implemented above.
Rewicked using 26g. It's a parallel coil of 7 wraps around a 1.4mm id. 0.5 ohms. Here are some pics to light up the thread.
Note: Seeing as my Kayfun 3.1's top cap is otherwise occupied at the moment, I needed to use the Lite Plus's top cap, which requires the Lite Plus's chimney base, which is about 2mm shorter than that of the 3.1. I don't know if the smaller chamber contributes to the increased flavour so I'll change it back at some point and leave an update.
And thanks for the credit card insulator tip @Rowan Francis! Implemented above.
I've found mine to get a little warm when running sub ohms after doing some stealth vaping
I would think it will.... Mine at 0.8 gets very hot
Sent from my GT-I9500 using Tapatalk
Sent from my GT-I9500 using Tapatalk
I'm chain vaping huge 5 second drags at the moment and it's the same temperature as a glass of tap water in the summer.
I skeem u got antifreeze in there haha 
Sent from my GT-I9500 using Tapatalk
Sent from my GT-I9500 using Tapatalk
so I couldn't wait any longer, the batteries for my SVD still haven't arrived. Didn't let that stop me, I decided to go balls to the wall and try making my very own coil, from scratch on my new Kayfun 3.1 clone from VapeMOB. Grabbed some Kanthal, as far as I can tell it could be 28g, wrapped it around a 2.4mm drill bit 8 times and slapped it on the deck, fired it a few times, pinched with tweezers and fired some more. It does take a while to get going but hey, that little ego 650mah battery only does so much. So, in with some cotton, assemble and top fill with some VM Amarula 12mg.
Wow, this juice tastes totally different, in the mPT3 it really wasn't very good, has a nasty "man parfume" aftertaste.... now, AMARULA!!
I have now discovered 2 things:
1. So, this is what a CLOUD looks like
2. Why the hell do people smoke weed when you can get a buzz like this
Loving it kwaai!
Wow, this juice tastes totally different, in the mPT3 it really wasn't very good, has a nasty "man parfume" aftertaste.... now, AMARULA!!
I have now discovered 2 things:
1. So, this is what a CLOUD looks like
2. Why the hell do people smoke weed when you can get a buzz like this
Loving it kwaai!
so I couldn't wait any longer, the batteries for my SVD still haven't arrived. Didn't let that stop me, I decided to go balls to the wall and try making my very own coil, from scratch on my new Kayfun 3.1 clone from VapeMOB. Grabbed some Kanthal, as far as I can tell it could be 28g, wrapped it around a 2.4mm drill bit 8 times and slapped it on the deck, fired it a few times, pinched with tweezers and fired some more. It does take a while to get going but hey, that little ego 650mah battery only does so much. So, in with some cotton, assemble and top fill with some VM Amarula 12mg.
Wow, this juice tastes totally different, in the mPT3 it really wasn't very good, has a nasty "man parfume" aftertaste.... now, AMARULA!!
I have now discovered 2 things:
1. So, this is what a CLOUD looks like
2. Why the hell do people smoke weed when you can get a buzz like this
Loving it kwaai!
View attachment 5427 View attachment 5428 View attachment 5429 View attachment 5430 View attachment 5431 View attachment 5432
Hehehe! I love your enthusiasm @BumbleBee! That coil looks brilliant! And for a first attempt! Colour me impressed!
Welcome to the wonderful world of rebuildables! What's the resistance? Just over 2 ohms I would think? NICE!
thats an awesome looking build 
I have no way of checking the resistance just yet, I was aiming for somewhere between 1.8 and 2.2, but hey, it lights up and makes fog
if you using Android get vapers toolbox pretty good for buildingI have no way of checking the resistance just yet, I was aiming for somewhere between 1.8 and 2.2, but hey, it lights up and makes fog
sent from my reonautical cloud machine
I'm an iPhone kinda guy, checked out some other builds on the forum beforehand to figure out how to go about this.
there is iphone app as well its more just to get you in the ball park maybe get a electro that reads ohm if u don't want ohm meter or even a multi meterI'm an iPhone kinda guy, checked out some other builds on the forum beforehand to figure out how to go about this.
sent from my reonautical cloud machine
Similar threads
