Coppervape Dvarw RTA

Carnival

Live. Chill. Vape.
ECIGSSA Donor
LV
18
 
Joined
18/12/17
Posts
1,074
Awards
23
Age
37
Location
JHB
I see @BumbleBee has stock of the Coppervape Dvarw plus the drop kit and AFC kits for it!

Is anyone considering trying this clone out?
 
I ordered one - they are the MTL version. The authentic, which I have, is amazing.
Very limited stock I see.
 
I ordered one - they are the MTL version. The authentic, which I have, is amazing.
Very limited stock I see.
I would love to hear your view on the authentic vs clone when you get it if you don't mind?
 
My impressions thus far on the Coppervape Dvarw MTL clone compared to the authentic. I bought the clone from The Vape Guy.

Coiled it with plain 28G Kanthal, 6 contact wraps around a 2.5mm ID at 1.1 Ohms. Wicked with Jellyfish cotton. Vaping at 15W. Using the 1.5mm air flow insert. It comes with a 1.2 mm air flow insert, which is closer to true MTL, but just too tight for me - I prefer a more airy MTL. One has to buy the Normal AFC Kit to get the bigger air flow inserts (1.5, 2.0 and 2.5 mm). A Tight AFC Kit is also available (0.8 and 1.0 mm).

My authentic was set up the same as above, except for the wicking method. The juice holes in the chamber of the clone are just too small for the Exocet method. So I just lifted the wick tails, slipped the chamber over the tails and inserted the chamber. Cut the wick tails at the top of the chamber and stuffed them into the chamber up against the little juice holes.

The bad:
The tolerances on the clone are not nearly as perfect. For example, the little chamber does not fit smoothly into the deck - one has to maneuver it with two hands to get it to slip in - well lubricated notwithstanding. The top cap of the chamber (the one some members forget to put back), stays stuck in the chimney when one unscrews to refill. But, nothing of a fatal nature fortunately.

The different:
The clone's air inlet on the outside is narrower. The juice holes in the chamber are much smaller. I have an idea this is a clone of an earlier version of the Dvarw. I have been vaping a 40PG/60VG juice in the clone without any problems at 15W (even did some chain vaping without adverse results - the bubbles keep coming), but a higher VG juice and higher power might create wicking problems. Seems to me the Large Juiceflow Chamber, which is sold separately, is closer to the chamber the authentic MTL comes with. My recommendation is that you spend the extra R60 and get it.

The good:
I am vaping the same juice (peach) in both. My palate cannot distinguish any difference in flavour. Flavour is outstanding in both. No leaking or even moisture thus far.

A more than worthwhile buy at the price imho. Should I pick up any problems going forward, shall let you know.

Clone left, authentic on the right.
qkg78zs.jpg


Tagging those who requested my impressions: @Carnival, @TheV, @Cornelius, @Room Fogger and @Dietz. FYI @BumbleBee.
 
Great writeup @Andre
Thanks for the efforts as always
 
Thanks for the tag @Andre, and of course for the detailed comparison. It is much appreciated.
It is good to know the performance is up there.

The top cap of the chamber (the one some members forget to put back), stays stuck in the chimney when one unscrews to refill.
That part should be called the goose cap :p
 
Thanks @Andre , it does seem worth it to get it based on your feedback, so Guess what was just added to my "Need more Vape stuff" list :-D
 
Thanks @Andre , it does seem worth it to get it based on your feedback, so Guess what was just added to my "Need more Vape stuff" list :-D
@Dietz, you asked me the other morning regarding the differences between clones and originals and I think @Andre describes it perfectly. It's those little details that make a difference between good enough and wel done. These are not huge differences but even with my attitude towards so called HE stuff I must admit they do matter.

If you change setups frequently it may be best to get a good clone but if you are at the setlling down point and intend sticking to a certain setup for more than a month or two, the original would be a worthwhile investment.

So I guess buying the clone to test and purchasing the original if results are positive theory does have merit as well.

Regards
 
I just pulled the trigger on one from @BumbleBee ... I'm a sucker for a good MTL vape at the end of the day and considering how on point the DL version is, I'm intrigued by this one
 
My Dvarw clone from BumbleBee is on it’s way, looking forward to trying this one out! :nod:
 
My impressions thus far on the Coppervape Dvarw MTL clone compared to the authentic. I bought the clone from The Vape Guy.

Coiled it with plain 28G Kanthal, 6 contact wraps around a 2.5mm ID at 1.1 Ohms. Wicked with Jellyfish cotton. Vaping at 15W. Using the 1.5mm air flow insert. It comes with a 1.2 mm air flow insert, which is closer to true MTL, but just too tight for me - I prefer a more airy MTL. One has to buy the Normal AFC Kit to get the bigger air flow inserts (1.5, 2.0 and 2.5 mm). A Tight AFC Kit is also available (0.8 and 1.0 mm).

My authentic was set up the same as above, except for the wicking method. The juice holes in the chamber of the clone are just too small for the Exocet method. So I just lifted the wick tails, slipped the chamber over the tails and inserted the chamber. Cut the wick tails at the top of the chamber and stuffed them into the chamber up against the little juice holes.

The bad:
The tolerances on the clone are not nearly as perfect. For example, the little chamber does not fit smoothly into the deck - one has to maneuver it with two hands to get it to slip in - well lubricated notwithstanding. The top cap of the chamber (the one some members forget to put back), stays stuck in the chimney when one unscrews to refill. But, nothing of a fatal nature fortunately.

The different:
The clone's air inlet on the outside is narrower. The juice holes in the chamber are much smaller. I have an idea this is a clone of an earlier version of the Dvarw. I have been vaping a 40PG/60VG juice in the clone without any problems at 15W (even did some chain vaping without adverse results - the bubbles keep coming), but a higher VG juice and higher power might create wicking problems. Seems to me the Large Juiceflow Chamber, which is sold separately, is closer to the chamber the authentic MTL comes with. My recommendation is that you spend the extra R60 and get it.

The good:
I am vaping the same juice (peach) in both. My palate cannot distinguish any difference in flavour. Flavour is outstanding in both. No leaking or even moisture thus far.

A more than worthwhile buy at the price imho. Should I pick up any problems going forward, shall let you know.

Clone left, authentic on the right.
qkg78zs.jpg


Tagging those who requested my impressions: @Carnival, @TheV, @Cornelius, @Room Fogger and @Dietz. FYI @BumbleBee.

I have Dwarv DL authentic and decided to buy MTL clone before I spend The money on the authentic and it's not much diff to the DL.
But I'm struggling to insert the coils. It keeps coming loose. The same coil I used in th DL I'm using in the MTL. With DL I had no problems. Could it be because it's clone, or because it's smaller then the DL or should I be using an even smaller coil then what I used in the DL.

Im not sure if I'm making myself clear. Hope u can help me.
TIA
 
I have Dwarv DL authentic and decided to buy MTL clone before I spend The money on the authentic and it's not much diff to the DL.
But I'm struggling to insert the coils. It keeps coming loose. The same coil I used in th DL I'm using in the MTL. With DL I had no problems. Could it be because it's clone, or because it's smaller then the DL or should I be using an even smaller coil then what I used in the DL.

Im not sure if I'm making myself clear. Hope u can help me.
TIA
No idea as I only have THE MTL versions. Think I have 27ga kanthal in both - no problems. Sorry.
 
Well well well..

I threw in a build using Kidney Puncher Ni80 24g wire, juice of choice is Machete.

Very, very nice vape!

I’m really enjoying MTL these days, I’ve officially converted. ;)
 
Cvarw incoming hopefully next week .... see there's a "V2" on 3F might get that as well to compare to the CV Dvarw ...

Also have the Authentic DL version , can see that maybe the MTL version is slightly better flavor wise due to smaller chamber.
 
So how is the experience of those who purchased the clone from Vape Guy? Flavour, wicking, leaking etc?

What exactly is the normal AFC kit? Will it be a more DL vape? I am a little wary of going for a MTL tank as I have this fear all my juices are going to taste like crap and I cannot imagine vaping at extremely low wattage?

I have been hooked on an Ammit 25mm single coil @ 0.3 and 40w for the last year - just sick and tired of the juice building up at the airflow control but have to endure cause the flavour is so good, better than the RTA's I've tried in the past. 99% of the time I vape bakeries and desserts and have noticed that they require a good RTA with a restricted DL hit to taste at its best. Fruity / Menthol vapes do good in most tanks, but not bakeries and desserts.
 
So how is the experience of those who purchased the clone from Vape Guy? Flavour, wicking, leaking etc?

What exactly is the normal AFC kit? Will it be a more DL vape? I am a little wary of going for a MTL tank as I have this fear all my juices are going to taste like crap and I cannot imagine vaping at extremely low wattage?

I have been hooked on an Ammit 25mm single coil @ 0.3 and 40w for the last year - just sick and tired of the juice building up at the airflow control but have to endure cause the flavour is so good, better than the RTA's I've tried in the past. 99% of the time I vape bakeries and desserts and have noticed that they require a good RTA with a restricted DL hit to taste at its best. Fruity / Menthol vapes do good in most tanks, but not bakeries and desserts.
My impressions earlier in this thread over here, @Wimmas. Since then it has been in constant use without any problems at all.
 
Back
Top