SXK BILLET BOX - Reviews & Discussions

[GerritVisagie]

Dude, I'm stressing out here.
I like my RDAS coz I like low ohm build with lots of airflow.... but dammit this bloody thing is intriguing AF


Sent from my iPhone 7+ using Tapatalk

 

[Christos]

Dude, I'm stressing out here.
I like my RDAS coz I like low ohm build with lots of airflow.... but dammit this bloody thing is intriguing AF


Sent from my iPhone 7+ using Tapatalk

The airflow on a BB is very restricted and more so on the insider.
The exocet atty has better airflow imho but it's also a small build deck.
Im sure you will be fine!

 

[spiv]

Just ordered mine now.
Was trying not to, resisted as long as I could.
So now I need to be schooled, fast.
What is this condensation plug everyone keeps talking about?
And I got the "insider" deck with it...
Hoping for more airflow with it.
Did I do the right thing?

I feel a little guilty now, like a naughty kid.


Sent from my iPhone 7+ using Tapatalk

You did the right thing. I had the Exocet in and I probably coiled it wrong, but the insider is so much better for me with the 4ml chimney. I don't leave home without it now. It also takes slightly bigger coils. Just watch the you tube video on how to wick it. You need so little cotton.

Let us know how it goes.

 

[GerritVisagie]

You did the right thing. I had the Exocet in and I probably coiled it wrong, but the insider is so much better for me with the 4ml chimney. I don't leave home without it now. It also takes slightly bigger coils. Just watch the you tube video on how to wick it. You need so little cotton.

Let us know how it goes.

Thanx man.
I'm starting to feel a bit more at ease with my choice now.
If all else fails, I have been contemplating getting MTL vape... for those times you need to be stealthy.


Sent from my iPhone 7+ using Tapatalk

 

[spiv]

Thanx man.
I'm starting to feel a bit more at ease with my choice now.
If all else fails, I have been contemplating getting MTL vape... for those times you need to be stealthy.


Sent from my iPhone 7+ using Tapatalk

Keep the air flow control in (you take it off to screw into a 510 to check your resistance and pulse your coils) and you can close it off a bit, lower your wattage and you have your stealth vape.

Also, fancy coils shine in the insider.

 

[GerritVisagie]

Keep the air flow control in (you take it off to screw into a 510 to check your resistance and pulse your coils) and you can close it off a bit, lower your wattage and you have your stealth vape.

Also, fancy coils shine in the insider.

That's good advise, thanx man.
Ok. What ohms do you guys run in there??
I was thinking 0.4 - 0.3 ish?


Sent from my iPhone 7+ using Tapatalk

 

[Scouse45]

Funnily enough I also have that "should I have done that..." feeling after ordering mine yesterday

Yes to both of u! Amazing! It's champion

 

[BioHAZarD]

Tomorrow is B Box day

 

[aktorsyl]

Tomorrow is B Box day

Luckily the Sirs use TCG. Dawnwing loves to use the "oh but the cargo flight was late last night" excuse
So I'm carefully optimistic about tomorrow myself. Trying to find some vids on building on the Exocet now. And some on how the BB actually works, heh

 

[BioHAZarD]

Luckily the Sirs use TCG. Dawnwing loves to use the "oh but the cargo flight was late last night" excuse
So I'm carefully optimistic about tomorrow myself. Trying to find some vids on building on the Exocet now. And some on how the BB actually works, heh

So far the Sirs have never dropped me

 

[Amir]

The Exocet is stellar if built and wicked correctly. The insider is more tricky but allows a bigger coil. You can make either work for after you've played around a bit with coil ID and positioning. I like a 3mm ID on the Exocet cause it kind of chokes the airflow and makes it more restrictive.


Sent from my iPhone using Tapatalk

 

[spiv]

That's good advise, thanx man.
Ok. What ohms do you guys run in there??
I was thinking 0.4 - 0.3 ish?


Sent from my iPhone 7+ using Tapatalk

I have a 0.73ohm, 2.5mm ID Clapton in there. Top of coil lined up with top of posts. Vape at 30w.

But like @Amir said, play around a bit.

 

[aktorsyl]

The Exocet is stellar if built and wicked correctly. The insider is more tricky but allows a bigger coil. You can make either work for after you've played around a bit with coil ID and positioning. I like a 3mm ID on the Exocet cause it kind of chokes the airflow and makes it more restrictive.


Sent from my iPhone using Tapatalk

Just out of interest sake, what kinda coil do you have in the Exocet?

 

[aktorsyl]

Found this:



He shows the Exocet too during the vid.

 

[Amir]

Just out of interest sake, what kinda coil do you have in the Exocet?

Got an alien at .4 ohm 2.5 ID currently but I preferred the .35 3mm ID. @spiv is spot on with the top of coil in line with top of post. Not top of post screw. Getting a custom set of coils specially made for the Exocet from @smileykumineet to try out. .25 ID .8 ohm alien and fused claptons. Another thing I noticed is that there's no marked difference between the aliens and fused claptons so far by my findings


Sent from my iPhone using Tapatalk

 

[Riaz]

My ohms keep jumping on mine.

But only when it's on the BB.

When I screw the exocet on a other mod the ohms are fine.

Its really annoying. So what I discovered is before I vape i need to first fire the thing a few times before pulling.

Am I doing something wrong?

 

[Lee]

Give the inside where the boro tank fits into a good wipe down.
In my experience, if its moist it plays with the ohmage

 

[spiv]

My ohms keep jumping on mine.

But only when it's on the BB.

When I screw the exocet on a other mod the ohms are fine.

Its really annoying. So what I discovered is before I vape i need to first fire the thing a few times before pulling.

Am I doing something wrong?

Take the Boro out and clean the condensation between the Exocet and the BB (Where the BB sticks out of the Boro). I used to have this problem too.

Strangely, never had this issue with the Insider.

 

[Lee]

Take the Boro out and clean the condensation between the Exocet and the BB (Where the BB sticks out of the Boro). I used to have this problem too.

Strangely, never had this issue with the Insider.

Trying the Insider today, I hope I'm not disappointed

 

[Riaz]

Take the Boro out and clean the condensation between the Exocet and the BB (Where the BB sticks out of the Boro). I used to have this problem too.

Strangely, never had this issue with the Insider.

I did that but still the same issue.

Its so bad man.

Last night I fired it having the panel off and the ohms were reading at 2.5 OMG imagine that dry hit

Strangely after firing it the ohms came back down

 

[Petrus]

I did that but still the same issue.

Its so bad man.

Last night I fired it having the panel off and the ohms were reading at 2.5 OMG imagine that dry hit

Strangely after firing it the ohms came back down

@Riaz , make sure that the part where you insert your drip tip is securely tight down, not to tight, use the back of your tweezer, so the atty can make good contact. I am sure it will solve your problem.

 

[Riaz]

@Riaz , make sure that the part where you insert your drip tip is securely tight down, not to tight, use the back of your tweezer, so the atty can make good contact. I am sure it will solve your problem.

Thank you I'll give that a try later.

 

[Sir Vape]

Also make sure your leads are trimmed. I assume something is touching the chimney

 

[aktorsyl]

So I have a question about the condensation.. is there any reason why you can't just stuff a bit of paper-towel or tissue paper into the slot at the bottom of the Boro tank (where the condensation plug would sit)? Other than the fact that it'd look cheap, but I mean.. I'm not going to order a condensation plug on its own now, I'd rather add it to my next bigger order.

 

[Petrus]

So I have a question about the condensation.. is there any reason why you can't just stuff a bit of paper-towel or tissue paper into the slot at the bottom of the Boro tank (where the condensation plug would sit)? Other than the fact that it'd look cheap, but I mean.. I'm not going to order a condensation plug on its own now, I'd rather add it to my next bigger order.

I think it can work, reminds me of a nose bleed, but remember not to block your airflow, something like a potato in a exhaust pipe