I’ve only heard good things about the ether and that is why I got one
yeah. you ether like it or you dont
iNtake MTL RTA
- Thread starter Rob Fisher
- Start date
yeah. you ether like it or you dont
After the excitement of finding another RTA with flavour and despite the issues of the stupid tiny revered post screws I got a couple more to play with. Want to experiment with coils and coil positions.
I never normally get anything other than stainless steel tanks but I got a gunmetal one for a change and it's a fail. The one post was loose and I can't work out how to tighten it... so that one is useless!
I also got another SS one and that one was fine... and after hassling with putting a coil in yesterday, today was a lot easier. I used a Bearded Viking coil because I wasted a different resistance and the 2.5mm MTL Alien came out at 0.72Ω. Again air plugs taken out and airflow fully open.
Popped it on the Vaporesso Gen Nano at 28 watts and once again really nice flavour.
I never normally get anything other than stainless steel tanks but I got a gunmetal one for a change and it's a fail. The one post was loose and I can't work out how to tighten it... so that one is useless!
I also got another SS one and that one was fine... and after hassling with putting a coil in yesterday, today was a lot easier. I used a Bearded Viking coil because I wasted a different resistance and the 2.5mm MTL Alien came out at 0.72Ω. Again air plugs taken out and airflow fully open.
Popped it on the Vaporesso Gen Nano at 28 watts and once again really nice flavour.
Drill a hole from the bottom to get to the screw. If it's gonna work don't know
@Rob Fisher 
Doesn't that lock/unlock mean the base can be taken apart? Did you try twisting it?.
Or isn't there something in the manual, if there is a manual?
Doesn't that lock/unlock mean the base can be taken apart? Did you try twisting it?.
Or isn't there something in the manual, if there is a manual?
No, that lock and unlock is to remind you which way to screw the post screws out... I posted in the Augvape FB group and messaged Mike Vapes and neither replied so I will take it to the boathouse and use some big tools to see if I can remove the deck from the base... I think it's press-fitted.
100% agree... but how is the question... I'm sure I will bugger it up completely when I take big tools to it.
Patience Skipper, you have two to play with so long. Rather wait for a response
Check if the positive pin can be removed. That might be the answer to taking it apart.
My most efficient vendor spotted the thread and has contacted Augvape and a new one will be dispatched in the AM! I never complained to him and a new one is on the way already! Man O Man I love proactive and efficient vendors! @JurgensSt for President!
You could use your Dremel and cut a slot in the offending screw, and then tighten it from the top with a jewelers screwdriver
I have the same issue as @Rob Fisher with the deck being loose.
Bought my RTA from Vape Africa and requested an replacement but for some reason I think this is going to be a battle to get right... Let's hope I'm wrong!
Bought my RTA from Vape Africa and requested an replacement but for some reason I think this is going to be a battle to get right... Let's hope I'm wrong!
That's a bummer! Why will it be a battle?
I don't know, they asking me a lot of questions like is the 510 pin tightened and did I maybe drop the RTA etc.
Keep us posted!
Well luckily it wasn't bad at all. They are sending me a new one, should arrive Wednesday. Also throwing in cotton and some coils to make up for the costs I have to undergo to send the faulty RTA back. I was wrong! No battle at all.
Hello gents and ladies
I need assistance with this RTA please.
I am not getting the flavour like you are all talking about. Please share some builds where I can see your coil placement and wicking.
I am thinking to get more flavour out of this atty I need to get the coil lower and not higher like other atties... Am I correct in saying that?
Looking forward to hear from you all.
I need assistance with this RTA please.
I am not getting the flavour like you are all talking about. Please share some builds where I can see your coil placement and wicking.
I am thinking to get more flavour out of this atty I need to get the coil lower and not higher like other atties... Am I correct in saying that?
Looking forward to hear from you all.
I'm using a MTL fused Clapton 2.5mm I have my coil "belly down" and pretty close to the air insert.
Have the 1.4 insert in and first 3 holes (smallest) open.
Wicking I cut off at the edge of the wick hole.
Thinned out very slight on the ends. Kinda a dam method.
Getting really good flavour with fruit MTL 12mg liquids
Last edited:
Similar threads
