Product information "SQuape E[motion] 2.0ml"
The SQuape E[motion] is a rebuildable tank atomiser which was developed and produced in its entirety in Switzerland. It is made by StattQualm to be used for the vaporisation of e-liquid. The SQuape E[motion] can be closed off completely by a slight rotation of the locking cap and is therefore absolutely leak-free. Because of the closed system the tank can be taken off the atomiser and transported empty or full. In daily use you only need to turn the cap to refill - that's it! Short circuits are virtually impossible, through clever design of current conduction, as well as due to the nonconductive surface of the whole atomiser-chamber (consisting of ematalised and anodized aluminum).
The SQuape E[motion] is a further development of the SQuape R[eloaded] and R, with some influences of the SQuape X[dream]. The atomiser is made for beginners as well as for experienced vapers. In addition to the innovative topfill and the possibility of completely closing the atomiser, the SQuape E offers improved poles for installing the wire. Another difference to the SQuape R is the revised Air-Flow-Control (AFC), which is also suitable for OpenDraw but also for mouth-to-lung with the addition of the MTL kit (1.6mm included).
Features
Product information "DECK "Be" SQuape E"
The power-single-coil deck! The Deck Be is characterized by its wide cotton pockets. The deck is ideally suited for cotton. Set a pin up to 3.5mm diameter onto the dentings and attach the wire ends to the poles. Then pull the cotton through the coil and shorten the cotton to the length of the base. Put the cotton down into the pockets - done. Very simple and easy to use.
For mouth to lung (MTL) please use the MTL Kit and screw from below the deck. You need a 2.5mm hex key.
Material:
Aluminum ematalised
Recommendation for this deck: 0.25 - 2 Ohm / 10 - 75W
Product information "DECK "We" wide SQuape E"
The Deck We is characterized by its very simple handling. The deck is ideally suited for cotton, fiber and mesh. Insert a pin up to 3mm diameter into the channel and attach the wire ends to the poles. Then pull the cotton through the coil and shorten the cotton to the length of the channel. The cotton should be adjusted and fill the channel well - done. There is not a more simple method for re-wicking an atomiser.
For mouth to lung (MTL) please use the MTL Kit and screw from below the deck. You need a 2.5mm hex key.
Material:
Aluminum ematalised
Recommendation for this deck: 0.5 - 2 Ohm / 10 - 25W
Available downloads:
The SQuape E[motion] is a rebuildable tank atomiser which was developed and produced in its entirety in Switzerland. It is made by StattQualm to be used for the vaporisation of e-liquid. The SQuape E[motion] can be closed off completely by a slight rotation of the locking cap and is therefore absolutely leak-free. Because of the closed system the tank can be taken off the atomiser and transported empty or full. In daily use you only need to turn the cap to refill - that's it! Short circuits are virtually impossible, through clever design of current conduction, as well as due to the nonconductive surface of the whole atomiser-chamber (consisting of ematalised and anodized aluminum).
The SQuape E[motion] is a further development of the SQuape R[eloaded] and R, with some influences of the SQuape X[dream]. The atomiser is made for beginners as well as for experienced vapers. In addition to the innovative topfill and the possibility of completely closing the atomiser, the SQuape E offers improved poles for installing the wire. Another difference to the SQuape R is the revised Air-Flow-Control (AFC), which is also suitable for OpenDraw but also for mouth-to-lung with the addition of the MTL kit (1.6mm included).
Features
- Top filling through locking cap. No removal of any parts needed. Simply turn the locking cap to open the filling holes and to close the liquid feed.
- Stepless airflow control
- Single- or dual coil usage with interchangeable decks.
- Adjustable 510 connector (gold plated)
- Deck is accessible even with full tank
- Nonconductive components inside the evaporation-chamber (deck and chimney) no danger of short circuits
- Very easy handling and coiling options
- Suitable for Temp. Control and V/W mode
- The tank can be completely closed and removed (even when full)
- Easy switching of the three positions vape, refill and closed by using the locking cap
- Diameter: 22 mm
- Height (without SQuip Tip and 510 connector): 52mm
- Weight: 55.5g
- Thread: 510
- Capacity: ~ 2.0ml
- Stainless steel components: stainless steel number 1.4404 / 316L
- Glass: Borosilicate glass
- Deck and chimney: Aluminum ematalised, anodised
- Centerpin: Ecobrass gold plated
- O-rings: nbr 70 shore
- 1x SQuape E[motion] incl. one Deck of your choice (interchangeable)
- 1x SQuip Tip E short
- 1x air reducer screw (MTL1.6mm)
- Spare screws and O-rings
- 1x Manual
Product information "DECK "Be" SQuape E"
The power-single-coil deck! The Deck Be is characterized by its wide cotton pockets. The deck is ideally suited for cotton. Set a pin up to 3.5mm diameter onto the dentings and attach the wire ends to the poles. Then pull the cotton through the coil and shorten the cotton to the length of the base. Put the cotton down into the pockets - done. Very simple and easy to use.
For mouth to lung (MTL) please use the MTL Kit and screw from below the deck. You need a 2.5mm hex key.
Material:
Aluminum ematalised
Recommendation for this deck: 0.25 - 2 Ohm / 10 - 75W
Product information "DECK "We" wide SQuape E"
The Deck We is characterized by its very simple handling. The deck is ideally suited for cotton, fiber and mesh. Insert a pin up to 3mm diameter into the channel and attach the wire ends to the poles. Then pull the cotton through the coil and shorten the cotton to the length of the channel. The cotton should be adjusted and fill the channel well - done. There is not a more simple method for re-wicking an atomiser.
For mouth to lung (MTL) please use the MTL Kit and screw from below the deck. You need a 2.5mm hex key.
Material:
Aluminum ematalised
Recommendation for this deck: 0.5 - 2 Ohm / 10 - 25W
Available downloads:
- Download SQuape E[motion] User Manual
- Download Wicking instructions
- Download FAQ SQuape E[motion] EN
Last edited:
