Dead Siren 22mm

Spongebob

Vaping Enthusiast
LV
26
 
Joined
25/3/16
Posts
821
Awards
22
Age
53
Location
Heidelberg gauteng
Need some help from the technical minded vapers recently traded a Siren 22mm from someone (brand new) that somehow came DOA? Worked 5 minutes and then started with the dreaded "no atomizer" on all my mods? Tinkered around but could not find anything? Tried someone else's advice and used thicker wire and swapped the grub screws and it worked for a day and a half and then started acting up again and has now passed on

I have checked 510 screw, coil seating, grub screws, everything i can think off, but no luck even had a multi meter on it, but could not find anything even tried running coil wire directly from one grub screw to the other, but nada



Is there anything anybody else can think of that i can check., because in all my years of vaping, the siren 22 is the best vape i have ever hadand if at all possible i would REALLY like to get her back to life?

Sent from my LYA-L09 using Tapatalk
 
I’ve had a similar issue in a rda once and it ended up being a tiny tiny piece of wire offcut that was causing a short. I had to take it all apart and wash and rinse and that solved the problem.

I hope you come right. Nothing more irritating.
 
I’ve had a similar issue in a rda once and it ended up being a tiny tiny piece of wire offcut that was causing a short. I had to take it all apart and wash and rinse and that solved the problem.

I hope you come right. Nothing more irritating.
I've taken it apart as far as I could the deck on the siren doesn't come out so can't check there

Sent from my LYA-L09 using Tapatalk
 
Need some help from the technical minded vapers recently traded a Siren 22mm from someone (brand new) that somehow came DOA? Worked 5 minutes and then started with the dreaded "no atomizer" on all my mods? Tinkered around but could not find anything? Tried someone else's advice and used thicker wire and swapped the grub screws and it worked for a day and a half and then started acting up again and has now passed on

I have checked 510 screw, coil seating, grub screws, everything i can think off, but no luck even had a multi meter on it, but could not find anything even tried running coil wire directly from one grub screw to the other, but nada



Is there anything anybody else can think of that i can check., because in all my years of vaping, the siren 22 is the best vape i have ever hadand if at all possible i would REALLY like to get her back to life?

Sent from my LYA-L09 using Tapatalk
With the coil on, the multimeter said open circuit or short ?


Sent from my SM-A730F using Tapatalk
 
Riddle me this there is no continuity between the areas marked with arrows when tested so how did it fire in the first place

Sent from my LYA-L09 using Tapatalk
 
Whoops pic attached

e1d09dfe22a649658a6400a45e67c29c.jpg


Sent from my LYA-L09 using Tapatalk
 
Now to test the rta, use the probes and touch it on the 510 connectors, like this. Notice the reading, this reading means there is continuity
a9d5dba1a19fbafc9a97006ed065cee3.jpg


Sent from my SM-A730F using Tapatalk
 
That is what i didand almost everywhere i touched it beeped except between the two points with the arrows

Sent from my LYA-L09 using Tapatalk
So I guessing u took out the positive pin(the screw) and the positive post, then u touched the probe on the 510 thread(the negative terminal) and the post, and u got no beep on the continuity tester. Is that right?

Sent from my SM-A730F using Tapatalk
 
Last edited:
If you put the positive pin back in the atty, do you get a reading on the pin+ and the post+?
And then also on the post+and the post -.
 
I have an atty that when its complete ,it does the same thing.its a kylin v1.
When I install a coil I get the error code no atty.
as soon as I undo the grub screws it starts reading the coil.
My question is. When your atty is completely assembled.do you get a reading from the positive pin to the positive post, and the same on the negative pin to the negative post.

Then also with the complete atty does it read between the two posts and pins respectively?
Trying to analize the actual cause
 
Ok rub a magnet on the atty sub assembly prefferably inside a cloth to avoid scratches.reasemble and check again on a mod
 
Back
Top