The Psyclone Citadel 22mm RDA was sent to me from @Pho3niX90 at The Vape Den for review purposes.
The RDA has no visible branding, and the Psyclone logo is located right at the bottom of the RDA and for me it gives it that "clean" finish.
Inside the box:
- Spare Parts Kit (Spare O-Rings, Spare Set Screws, Squonk Plug Screw Tool)
- Citadel RDA
- Accessory Bag
Pros :
- Standard positive squonk pin and plug for dripping included
- Good quality post screws
- Over squonk protection
- Juice well is on par with most commercial RDA's
- Easy to build on build deck
- Good clean design lines
- Chamber reducer to enhance flavor and warmth
- Handles all flavour profiles really well (bakery, fruits, menthols)
- No extreme whistling noise
Cons :
- Airflow control adjustability
- Top cap gets really hot (chain vaping)
- Top cap doesn’t lock into place
- Requires the coil to sit low
- Once leads are snipped they are very close to the edge
- Post screw heads are a little bit small
RDA Specifications:
- 22mm Stainless Steel RDA
- Peek Insulators
- Black Delrin Drip Tip
- Unique Ultem Chamber Reducer To Enhance Flavor and Warmth
- Dual Sided Slotted Post with Large Flathead
- Securing Set Screws
- Hadaly Styled Airflow Angled Downward for
- Minimizing Leaks
- Integrated Squonk 510 pin (Plug Screw is Located in the Bottom of the Deck)
- Width: 2.50 (in)
- Height: 2.50 (in)
- Depth: 1.50 (in)
Setup used by myself :
- iJust 2 Mod
- Coilology Framed Staple Prebuilt Coils
* Longevity: 3.5 weeks daily usage.
* Resistance: 2-28/4-.3*.1/36 (0.3ohm)
- GeekVape - Feather Cotton or
- Swag Supreme Cotton

Building The Deck :
Although it is a single coil RDA, there are 4 post holes which are sliced into the ends of each post with an angle up to keep your coils in place while tightening down. Having 4 holes means you can wrap your coils either way and easily install the coils. I found it is best to install the coils belly down.
In Conclusion:
Yes the RDA is a little bit on the pricey side and some would consider this as "High-end", but it is a phenomenal piece to add to your vaping equipment.

Available for purchase here :
https://www.thevapeden.co.za/products/psyclone-citadel-22mm-rda
Coilology Framed Staple Prebuilt Coils:
https://www.thevapeden.co.za/products/coilology-framed-staple-prebuilt-coils
GeekVape - Feather Cotton:
https://www.thevapeden.co.za/products/geek-vape-feather-cotton
Swag Supreme Cotton:
https://www.thevapeden.co.za/products/swag-supreme-cotton
Please note:
This review is the views and opinion of a personal nature and by no means reflect any organisational views or stereotypes. These are honest and reliable opinions and is not sponsored by any person or company. These reviews are also not done for any financial gain.
Please feel free to ask any questions and share your thoughts.
COPYRIGHT PROTECTED © The Vaping Chanel
The RDA has no visible branding, and the Psyclone logo is located right at the bottom of the RDA and for me it gives it that "clean" finish.
Inside the box:
- Spare Parts Kit (Spare O-Rings, Spare Set Screws, Squonk Plug Screw Tool)
- Citadel RDA
- Accessory Bag
Pros :
- Standard positive squonk pin and plug for dripping included
- Good quality post screws
- Over squonk protection
- Juice well is on par with most commercial RDA's
- Easy to build on build deck
- Good clean design lines
- Chamber reducer to enhance flavor and warmth
- Handles all flavour profiles really well (bakery, fruits, menthols)
- No extreme whistling noise
Cons :
- Airflow control adjustability
- Top cap gets really hot (chain vaping)
- Top cap doesn’t lock into place
- Requires the coil to sit low
- Once leads are snipped they are very close to the edge
- Post screw heads are a little bit small
RDA Specifications:
- 22mm Stainless Steel RDA
- Peek Insulators
- Black Delrin Drip Tip
- Unique Ultem Chamber Reducer To Enhance Flavor and Warmth
- Dual Sided Slotted Post with Large Flathead
- Securing Set Screws
- Hadaly Styled Airflow Angled Downward for
- Minimizing Leaks
- Integrated Squonk 510 pin (Plug Screw is Located in the Bottom of the Deck)
- Width: 2.50 (in)
- Height: 2.50 (in)
- Depth: 1.50 (in)
Setup used by myself :
- iJust 2 Mod
- Coilology Framed Staple Prebuilt Coils
* Longevity: 3.5 weeks daily usage.
* Resistance: 2-28/4-.3*.1/36 (0.3ohm)
- GeekVape - Feather Cotton or
- Swag Supreme Cotton

Building The Deck :
Although it is a single coil RDA, there are 4 post holes which are sliced into the ends of each post with an angle up to keep your coils in place while tightening down. Having 4 holes means you can wrap your coils either way and easily install the coils. I found it is best to install the coils belly down.
In Conclusion:
Yes the RDA is a little bit on the pricey side and some would consider this as "High-end", but it is a phenomenal piece to add to your vaping equipment.

Available for purchase here :
https://www.thevapeden.co.za/products/psyclone-citadel-22mm-rda
Coilology Framed Staple Prebuilt Coils:
https://www.thevapeden.co.za/products/coilology-framed-staple-prebuilt-coils
GeekVape - Feather Cotton:
https://www.thevapeden.co.za/products/geek-vape-feather-cotton
Swag Supreme Cotton:
https://www.thevapeden.co.za/products/swag-supreme-cotton
Please note:
This review is the views and opinion of a personal nature and by no means reflect any organisational views or stereotypes. These are honest and reliable opinions and is not sponsored by any person or company. These reviews are also not done for any financial gain.
Please feel free to ask any questions and share your thoughts.
COPYRIGHT PROTECTED © The Vaping Chanel
Last edited: