Did way too much juice testing this week so the Sunday PitStop was a dozen DVarw's!
Major pitstop
- Thread starter Silver
- Start date
I watched all the EPL football
Courtesy of @TonySC I got my hands on an aromamiser supreme 25 mm. Now if I said to my mates that I was tinkering with an aromamiser, they would immediately think that I have been feeling up the perfume makers daughter, but that just goes to show the caliber of mates that I have.
Since I broke my Pro tank 4 I have been wanting a "big" tank. As I spend some time looking at reviews of the older stuff I knew this tank would suit. So when it came up I grabbed it. Big tank indeed, even on the NCV2 it still looks big. Huge 7mm tank sitting on top of an RDTA type set up. I like the idea of the push in deck and what got me going was the chance to do a vertical build on the Velocity-style deck.
2 coils needed, I went with Coil master 22 awg wire, at ten wraps would give me 0.6/2 = 0.3. Sounds just about right. My little ohm meter confirmed this with the first coil. Fitting the coils was a breeze. Wicking , errm not so much. It takes a little finagling (here we go again, you did what! to the perfumers daughter?) to get the cotton at the bottom just right. Here you have to thin out your cotton before you feed it through and judge the thick bit for the centre of the coil. Then get the cotton sitting on top of the wicking juice ports. A little strumming and pulsing and those coils are like a boss. As usual I broke in the cotton by gently dripping on the nice fluffy cotton poking out of the top of the coils.
Since I broke my Pro tank 4 I have been wanting a "big" tank. As I spend some time looking at reviews of the older stuff I knew this tank would suit. So when it came up I grabbed it. Big tank indeed, even on the NCV2 it still looks big. Huge 7mm tank sitting on top of an RDTA type set up. I like the idea of the push in deck and what got me going was the chance to do a vertical build on the Velocity-style deck.
2 coils needed, I went with Coil master 22 awg wire, at ten wraps would give me 0.6/2 = 0.3. Sounds just about right. My little ohm meter confirmed this with the first coil. Fitting the coils was a breeze. Wicking , errm not so much. It takes a little finagling (here we go again, you did what! to the perfumers daughter?) to get the cotton at the bottom just right. Here you have to thin out your cotton before you feed it through and judge the thick bit for the centre of the coil. Then get the cotton sitting on top of the wicking juice ports. A little strumming and pulsing and those coils are like a boss. As usual I broke in the cotton by gently dripping on the nice fluffy cotton poking out of the top of the coils.
Attachments
Last edited:
So how does it vape, you may ask, well just like the perfumers daughter it does a lot of things very well. I like the juice control, wide open and I can see one big bubble when you open it after refilling. About half way gives me good bubbles and no dry hits. The airflow is really good, lots of options here from a tight RDL to full DTL. I am running one dot turned on the noisy. Plenty of flavour, vapour cloud very good and not too hot which I like. So just as I go the Intake dialed in, now I have another that is very satisfying indeed.
Attachments
Thanks @Grand Guru
It is something I have wanted to have a go at for some time. I would build vertical coils for the sub ohm tank coils that I would strip some times. It's a bugger now though because I can't wait to strip it down again to see how those coils and cotton is doing. The coils are the same 22 awg Coil master wire that I use in many of my builds so I know they will clean well. Wicking is working fine, next time I have to see if I can wick with one long cotton strip and take the wick over the top of the two coils. One for me. First time that foul mouthed Aussie wicked it, he stuffed it up.
It is something I have wanted to have a go at for some time. I would build vertical coils for the sub ohm tank coils that I would strip some times. It's a bugger now though because I can't wait to strip it down again to see how those coils and cotton is doing. The coils are the same 22 awg Coil master wire that I use in many of my builds so I know they will clean well. Wicking is working fine, next time I have to see if I can wick with one long cotton strip and take the wick over the top of the two coils. One for me. First time that foul mouthed Aussie wicked it, he stuffed it up.
Like this. I have to say much better than leaving the tails out of the top. You can just see a bit of gunking up on the top of the coil, but the wick is clean and this is after a full weekend.
Attachments
Rebuilding by candle light.... so romantic!
Weekend Dvarw Pitstop!
I laughed out loud at this remark. Thanks, I needed that during load shedding.
Its time... some cleaned, some wicked, all fun!
I need a drop in my life
Stop it
Stop it
Ok, ok, better option... you can have mine... if ever you grow tired of it I shall take it back.
And the Tauren beest any idees like this one lol
Ha.. haha... I walked right into that one... will stick your name on it if I ever get gatvol of it, might only be 2 days after my funeral though...
Oh yes you did lol. I have a lot of patience, just do t know if I have a lot of time though
I'll be here waiting.
Hi, is that the Holiday INN, Yes, good , can I please book a room for three ...........
Here we go again!
Work in progress, going slow tonight
All done and ready for the week
Great to see that you are having fun with it!
Similar threads
