Makes sense. I will change to SS round wire 24Awg and will go for about 35-40W
And then!!!
- Thread starter Resistance
- Start date
That looks more like it!
Could be the mod was confused
or not picking up the MTL wire. This same ATTY just read 2.4 ohms on another mod.I really need an ohm reader now, but you've seen the pics so I didn't lie
How many wraps is 24G and what is the internal diameter of the coil?
Not sure now. I will count the next time I refill
If it's reading completely different resistances on three different devices it's not an ohm reader you need but a miracle!Could be the mod was confused
I really need an ohm reader now, but you've seen the pics so I didn't lie
From the pic I count about ten wraps each on a 3mm screwdriver
If it's 8-9 wraps ID 2.5mm, Twisp thingy is a closest read. Maybe you need to clean the 510 connector on the other mods.
In any case I would ditch the SS wire for the mech mod (resistance is changing with the temperature) and use only NI80 or Kanthal.
Yes,that sounds like a plan.could also be that resistance changed after I opened the ATTY.maybe that was a good thing,could have shorted before I opened it.
???
From what is said. The guy that shot him...didn't shoot him or something.
@Resistance magic coil!
If it shorted mod would warn you, but loose screws on the deck or bad connection on 510 could cause the higher reading.
Ok I know what changed on my ATTY.
I will investigate it further.
I will investigate it further.
For there to be only one gunman as claimed a certain bullet needed to injure two people kill Kennedy while turning corners, reversing and doing a triple somersault!
I ran a magnet over the coil. And I am reading up on it right now ,because I don't know if it has something to do with it.
Might be, confused about this,but I will stress about this after I finish the mod.
When the mod measured 1 ohm it didn't burn the coil or wick at the wattage it was set so even though it's confusing as to why it happened. It still didn't cause a failure of any kind.
I'll just have to double/tripple check the ATTY before I use it on an unregulated set-up.
I'll just have to double/tripple check the ATTY before I use it on an unregulated set-up.
Last edited:
Regarding your initial question :
I bought the original Noisy Cricket during the vaping dark ages. It scared the living @#$%^& out of me. I think that my response wasn't mine alone. In the words of Jeremy Clarkson ...P....O....W....E....R !!!!!!!!
I can see why the new version offered both the parallel and series options as well as the pot.
I would prefer riding bareback on a porcupine to building my own series mod.
You are a very experienced vaper and may, therefore, want to go this route. I am too much of a coward to try it.
Good luck and please let us know how it goes.
I bought the original Noisy Cricket during the vaping dark ages. It scared the living @#$%^& out of me. I think that my response wasn't mine alone. In the words of Jeremy Clarkson ...P....O....W....E....R !!!!!!!!
I can see why the new version offered both the parallel and series options as well as the pot.
I would prefer riding bareback on a porcupine to building my own series mod.
You are a very experienced vaper and may, therefore, want to go this route. I am too much of a coward to try it.
Good luck and please let us know how it goes.
I will take @Timwis to mind if I go series. I will try to build much higher resistance coils both bigger ø and longer if I can fit it in an RTA/RDA.
Thanks for the concern.
This still puzzles me. ran a magnet over the coils to pick up anything that's not coil ,but the resistance on the packaging matched the coil reading. So I'm thinking the round wire might have not made proper contact till it either heated up, or till I opened the ATTY @alex1501 .what's your take take on this bro. If it was just this wire then 9-10 wraps should be about 2ohms???
That would be the most probable cause. You can double check screws holding a wire also check the one at the bottom of the tank (510 connector).
using SS in mechs is great because the resistance increases as you heat up the coil. making you mech have a boost initially due to the lower resistance.
I get your point for dripping, but not so much for an RTA. Greatest thing about vaping is that you can always set it to the personal preference.
Similar threads
