Hohm Slice (By Hohm Tech)

[daniel craig]

MATERIALS​

1. 101W
2. 26650 powered
3. Flatline ohm 0.000001
4. Temp Control - EVERYTHING (YES, kanthal & ceramic infused too)
5. Solo Update & Charge port
6. Adaptive Fast Charge IC* (Charge At Up To 3A)
7. Baked Ceramic Symbol Layer*
8. 31.9% less surface area than Wrecker G2
9. 4 button system with 3 button layout
10. Dual-Release point battery door (slide with hand, or lift with finger)
11. 510 with deep pocket & high tensile pin
12. Engineered in California...not just “designed”
13. 500 DAY WARRANTY

*Available on Limited Edition model (as shown), release date: May 2016.

______________________________________________________________________________________

SPECIFICATIONS​

. Chip: FSK1, TC-XT Series (T24SMX v3.2)

. Battery: 26650-powered

. Temp Control: Ni, SS, Ti, NiCr, K, W, & Ceramic Infused (YES, temp control EVERYTHING. No limits here)

. Wattage Output; 10W -101W (all modes)

. Voltage Output; FSK1 Intellichip, automation

. Temperature Range: 200°F - 700°F

93°C - 372°C

. Ohm Resistance Range: Flatline - 0.000001Ω - 3Ω

. Temp/Watt Increments：0.1 (10-49.9: WATTS MODE)

1.0(50-101: WATTS MODE)

1.0°C (TEMP MODE)

10.0°F (TEMP MODE)

______________________________________________________________________________________

FEATURES​

We believe in no limits. We believe in precision. We believe in efficiency. We put quality & safety above all. welcome to the world's first device that incorporates the best of the best every mod has ever offered... now you can put all other mods to rest...

• Temperature Control the "impossible"... KANTHAL NICHROME CERMIC INFUSED & everything else

+ Supports TC (K1) Kanthal, (NiCr) Nichrome, (W) Tungsten, (Ni) Nickel, (Ti)Titanium. (SS 304,316,317,430) Stainless Steel, Ceramic lnfused coils & tanks...no limits here...

• Integrated FSK1 Intellichips execute multiple tasks

+ Supports variable output banding on amperage & wattage adjustments so chip does not fluctuate in wide variations *Result: increased battery life, coils, cotton, jnd (educes battery amperage stress

• 101W yep, ONE HUNDO + 1
• Solo Update & Adaptive Fast Charge Port6

+ Supports 1.5hr charge on LE4 & 4hr on SE6

• Baked ceramic symbol layer6
• Dual-Release point battery door (slide with hand, lift with finger)
• Battery contact footprint has 47% more surface area than traditional 150W-250W + device average

+ Candidates of measure: Fuchai 200W, Snow Wolf 200W, IPV3-Li 165W, Sigelei 15OW TC. Tesla 160W, WiSmec RX250

+ Eliminates battery contact stress, & battery power spiking

• . Inside & Out 100% engineered and designed in the United States (not just "designed")
• System menu & instruction manual written by English vapers, in English
• Concaved FIRE button for finger ergonomics
• Flatline 0.0000010Ω - 3Ω (run it all!...no limits here)
• full-face push pin with high-tension spring 510

+ Ensures pure contact for utmost energy flow

* Result: eliminates another energy stress point

• 64Kb Onboard ROM to handle all computations of proprietary algorithms and EPT2: valuations

______________________________________________________________________________________

Here are some video links:

 

[OhmzRaw]

Looks like what I've been looking for all along. Looks stunning and 3amp charging!! and killer features! Would love to get one of these

 

[Silver]

So how does this device do temp control on kanthal?
I thought the change in resistance for kanthal as it heats up was too slight for these mods to do temp control on kanthal.

Is it just that ot can sense very small changes in resistance?
Or do you think it has a thermometer in there? Lol.

 

[daniel craig]

So how does this device do temp control on kanthal?
I thought the change in resistance for kanthal as it heats up was too slight for these mods to do temp control on kanthal.

Is it just that ot can sense very small changes in resistance?
Or do you think it has a thermometer in there? Lol.

How it works is a proprietary algorithm that integrates EPT (electrical ping timing). TCR is also used (kind of). FSK uses the ohm spread and not TCR value (however both area related directly to resistance change in relation to temp change). So with EPT and ohm spread, FSK is actually able to evaluate kanthal (and any other conductive material under the sun)...so, it can evaluate kanthal temp change. As kanthal gets hotter, the EPT valuations change (resistance changes but too small to reliably measure and rely on for accurate, consistent, and stable performance). It is quite complex to describe other than...it works, whereas TCR does not.

 

[Silver]

How it works is a proprietary algorithm that integrates EPT (electrical ping timing). TCR is also used (kind of). FSK uses the ohm spread and not TCR value (however both area related directly to resistance change in relation to temp change). So with EPT and ohm spread, FSK is actually able to evaluate kanthal (and any other conductive material under the sun)...so, it can evaluate kanthal temp change. As kanthal gets hotter, the EPT valuations change (resistance changes but too small to reliably measure and rely on for accurate, consistent, and stable performance). It is quite complex to describe other than...it works, whereas TCR does not.

Ok, many thanks @daniel craig
So its using a different method then but still based on the change in resistance as the temp changes.
Sounds like good innovation

 

[daniel craig]

Ok, many thanks @daniel craig
So its using a different method then but still based on the change in resistance as the temp changes.
Sounds like good innovation

Yes, using these 3 methods it's able to TC any wire which even makes it better than the DNA which used TCR only.

Hohm tech really did a good job with their chip. One of the best out there and cheaper than the DNA

 

[Silver]

Thanks @daniel craig
Am just happy to see good innovation happening
Improved vaping and improved cost. Real win!

Will be keeping an eye on this, thanks for the info

 

[daniel craig]

Thanks @daniel craig
Am just happy to see good innovation happening
Improved vaping and improved cost. Real win!

Will be keeping an eye on this, thanks for the info

I really hope vendors will be bringing these in. This mod is excellent according to the owners of them and I have to have both the Hohm slice, and the G2 in my life

 

[daniel craig]

Looks like what I've been looking for all along. Looks stunning and 3amp charging!! and killer features! Would love to get one of these

Definitely a winner. I think this is the only mod I've seen that can be charged at 3A. This has the same great feautures as the G2 but smaller and has a very nice design, it's also cheaper. If you don't really vape at very high wattages then this will be the one to get. There's basically no limits with this mod at all, use any wire, build any resistance, TC everything. The FSK chip to me beats the DNA.

 

[Jono90]

my only concern with high rate charging is degraded long term battery life.
i notice a large difference in battery heat when charging batteries at 1a instead of 375ma so i could only imagine 3a
still would be nice if you in a rush and need the speed, But i wouldnt use it all the time

 

[daniel craig]

@Jono90 26650 mostly have a .8C charge rate. So a 4200mAh cell will charge at 4.2 x .8 = 3.36. However, as an added safety feature, hohm tech has built in an amp monitor which essentially just watches for any amp irregularities. If battery is showing inconsistent amp delivery, the AFC IC will pull back power and charge below amp irregularities are being discovered.

Their (Hohm Tech) Hohm Grown cell is a full 1C charge rate, so it can actually charge at up to 4.3A (safely).

 

[OhmzRaw]

I hope this one makes it here. I prefer this one more than the G2 because of its size, don't really feel the need to have a high wattage device.

 

[kev mac]

View attachment 59922

MATERIALS​

1. 101W
2. 26650 powered
3. Flatline ohm 0.000001
4. Temp Control - EVERYTHING (YES, kanthal & ceramic infused too)
5. Solo Update & Charge port
6. Adaptive Fast Charge IC* (Charge At Up To 3A)
7. Baked Ceramic Symbol Layer*
8. 31.9% less surface area than Wrecker G2
9. 4 button system with 3 button layout
10. Dual-Release point battery door (slide with hand, or lift with finger)
11. 510 with deep pocket & high tensile pin
12. Engineered in California...not just “designed”
13. 500 DAY WARRANTY

*Available on Limited Edition model (as shown), release date: May 2016.

______________________________________________________________________________________

View attachment 59927

SPECIFICATIONS​

. Chip: FSK1, TC-XT Series (T24SMX v3.2)

. Battery: 26650-powered

. Temp Control: Ni, SS, Ti, NiCr, K, W, & Ceramic Infused (YES, temp control EVERYTHING. No limits here)

. Wattage Output; 10W -101W (all modes)

. Voltage Output; FSK1 Intellichip, automation

. Temperature Range: 200°F - 700°F

93°C - 372°C

. Ohm Resistance Range: Flatline - 0.000001Ω - 3Ω

. Temp/Watt Increments：0.1 (10-49.9: WATTS MODE)

1.0(50-101: WATTS MODE)

1.0°C (TEMP MODE)

10.0°F (TEMP MODE)

______________________________________________________________________________________

FEATURES​

We believe in no limits. We believe in precision. We believe in efficiency. We put quality & safety above all. welcome to the world's first device that incorporates the best of the best every mod has ever offered... now you can put all other mods to rest...

• Temperature Control the "impossible"... KANTHAL NICHROME CERMIC INFUSED & everything else

+ Supports TC (K1) Kanthal, (NiCr) Nichrome, (W) Tungsten, (Ni) Nickel, (Ti)Titanium. (SS 304,316,317,430) Stainless Steel, Ceramic lnfused coils & tanks...no limits here...

• Integrated FSK1 Intellichips execute multiple tasks

+ Supports variable output banding on amperage & wattage adjustments so chip does not fluctuate in wide variations *Result: increased battery life, coils, cotton, jnd (educes battery amperage stress

• 101W yep, ONE HUNDO + 1
• Solo Update & Adaptive Fast Charge Port6

+ Supports 1.5hr charge on LE4 & 4hr on SE6

• Baked ceramic symbol layer6
• Dual-Release point battery door (slide with hand, lift with finger)
• Battery contact footprint has 47% more surface area than traditional 150W-250W + device average

+ Candidates of measure: Fuchai 200W, Snow Wolf 200W, IPV3-Li 165W, Sigelei 15OW TC. Tesla 160W, WiSmec RX250

+ Eliminates battery contact stress, & battery power spiking

• . Inside & Out 100% engineered and designed in the United States (not just "designed")
• System menu & instruction manual written by English vapers, in English
• Concaved FIRE button for finger ergonomics
• Flatline 0.0000010Ω - 3Ω (run it all!...no limits here)
• full-face push pin with high-tension spring 510

+ Ensures pure contact for utmost energy flow

* Result: eliminates another energy stress point

• 64Kb Onboard ROM to handle all computations of proprietary algorithms and EPT2: valuations

______________________________________________________________________________________

Here are some video links:

I am waiting for my Hohm Slice that I ordered a week ago and was wondering if any forum members own or have tried one.I found it at Go-Evape for $49.00usd.w/free shipping.

 

[Blu_Marlin]

I am waiting for my Hohm Slice that I ordered a week ago and was wondering if any forum members own or have tried one.I found it at Go-Evape for $49.00usd.w/free shipping.

IIRC I think @Sprint has a HOHM Slice. maybe he can give some input.

 

[Choked Blood Flow Fiend]

@kev mac yes I own one. First tell me why you gave me a disagree rating today

 

[daniel craig]

I am waiting for my Hohm Slice that I ordered a week ago and was wondering if any forum members own or have tried one.I found it at Go-Evape for $49.00usd.w/free shipping.

You will be happy with this mod. Keep in mind there is a slight learning curve as to how to TC kanthal correctly etc. You can watch the video in YouTube by hohm tech. The guy does an excellent video in detail as to how to use the mod.

 

[Rude Rudi]

Got mine to today... So far so good!

 

[daniel craig]

Got mine to today... So far so good!

You will love it, check out their video in YouTube if you need any help.

 

[Rude Rudi]

I will - need some help with the settings...


Sent from my iPad using Tapatalk

 

[Choked Blood Flow Fiend]

Press mode 3x for a different menu and you can cycle through 3 settings menus.

To enter advanced menu hold down mode and +- buttons for 3 seconds.

Don't bother trying Kanthal as finding the FSK curve is difficult, I think we need to start a thread for FSK values on Kanthal to see what people get working.

 

[Choked Blood Flow Fiend]

Always fire mod before putting on new atomiser to reset ohm detection.

 

[daniel craig]

Press mode 3x for a different menu and you can cycle through 3 settings menus.

To enter advanced menu hold down mode and +- buttons for 3 seconds.

Don't bother trying Kanthal as finding the FSK curve is difficult, I think we need to start a thread for FSK values on Kanthal to see what people get working.

It will always differ, the mod uses various techniques to determine the value. Check out their video and see how they do it.

 

[Larry]

currently running 0.94 ohm 26/32g clapton 6 wrap single coil in Kanthal TC Mode. FSK - 35%, 30W, 450 F = beautiful vape

 

[daniel craig]

Also keep in mind that it won't be so accurate when using RTA or RDA because when using these there are other factors that affect the FSK curve such as wicking, airflow etc. It will work best when using a tank.

 

[incredible_hullk]

wow keen...anything that can tc kanthal is a win but..alien technology?